|
The refilling procedure for OKI Toner Cartridges is simple in most cases – make a hole (or uncover a hole) in the cartridge, refill it, and seal it. For specific instructions on your specific model please locate your model in our instruction booklet. While refilling a toner cartridge poses no significant risk to your health,
We ask you to refill your OKI Laser Toner outside whenever possible and always use common sense when handling the toner hole making tool or when pouring the toner.
OKI TONER REFILLS GENERAL INSTRUCTIONS – PLEASE READ BEFORE REFILLING
Thank you for purchasing OKI Toner Refill , If you have any questions about the use of these products, please check our FAQ’s below or email our technical support at
support@topinks.co.uk - BUY TONER REFILLS SECURELY ONLINE
Top Toner Refills are dedicated to providing high quality products at prices that allow our customers to save significantly compared to buying original cartridges. Refilling your OKI toner cartridge also helps the environment as your empty toner cartridge can be revived instead of landing up in a landfill.
The refilling procedure is simple in most cases – make a hole (or uncover a hole) in the cartridge, refill it, and seal it. For specific instructions on your specific model please locate your model in our instruction booklet. While refilling a toner cartridge poses no significant risk to your health, we ask you to refill outside whenever possible and always use common sense when handling the toner hole making tool or when pouring the toner.
Using the Electric toner hole making tool:
This tool is an electrical appliance that is used to make a hole in the cartridge by first heating up to a desired temperature. Be careful when handling this tool so that you don’t burn yourself or anything around you, the tool gets very HOT! You will need to wait for the tool to heat up for about 3-5 minutes before using it to burn a hole in the desired location on the cartridge (see specific cartridge instructions for location of hole). While waiting for the tool to heat up or cool down, rest the tool on the tool stand as shown in this diagram above.
Pouring the toner:
To our knowledge, the average DIY refiller’s exposure to fumes presents no significant health hazard in normal use. We recommend refilling in a well ventilated room or outside to minimize
the exposure to fumes. For extra protection, we advise that you wear a dust mask.
FAQ’s FOR TONER REFILL KITS
1. Will your toner harm my OKI printer or photocopier?
If you follow our simple instructions and inspect your work before reinstalling your cartridge, there is no way the cartridge you refill can harm your machine.
2. Will the use of your toner void my warranty?
Nope! In fact, it is against the law (the Sherman and Clayton Anti-Trust Acts, to be specific) to tie the purchase or use of a particular supply to the warranty.
3. Are there any hazards involved with the handling of toner?
HP describes toner as “Toner is a nontoxic substance composed of plastic, iron, and a small amount of pigment.”
Much like the fumes released from gasoline in cars or from active or passive smoking or even from inert dust and chemicals in the environment, the exposure to fumes from toner or from burning a hole in the cartridge (when necessary) could of course be hazardous. To our knowledge, the average DIY refiller’s exposure to fumes presents no significant health hazard in normal use. We recommend refilling in a well ventilated room or outside to minimize the exposure to fumes. For extra protection, wear a dust mask.
4. How many times can I refill my OKI toner cartridge?
An average of three times (It varies depending on cartridge type). The range is from 1 or 2 times, to 5 or more times. Quality and page yield will decrease the more times a cartridge is refilled. While we have had reports from some users that they have been able to use our toner an even greater number of times on a given empty, the simple (and obvious) rule of thumb is, continue to use our toner until you are no longer satisfied with the print quality.
5. Why are the kits named after formulas instead of names of printers?
The “engine” in your laser printer is also manufactured to be used in dozens, even hundreds of other printers.
6. If the refilled cartridge using your toner won’t hurt the printer, what, if anything, can go wrong?
Just like a new cartridge, if there is ever anything that goes wrong, it normally shows up on the printed output. If you notice spots, dots, blank spots or voids showing up on the printed page (in a pattern that repeats several times down the page), then the cartridge has reached the end of its useful life and needs to be replaced. A razor sharp, pencil thin line appearing on the page also indicates a cartridge has reached the end of the line.
7. Is your toner made by the same company that makes the brand-name cartridge toner?
There is no way to know for sure. Many laser printer manufacturers do not make their own toner.
We use toner formulas that match as closely as possible the properties of the original toner they are replacing. Our toners are tested not only for excellent quality prints like the original, but also for page yield so that you get about the same amount of printed pages as the original cartridge on the first refill.
General Refilling Procedures OKI Toner Cartridges:
Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before using. Position the copper bit on the cartridge in the spot indicated by the photograph and push gently until it melts a hole in the cartridge. Remove the tool, place it back on its stand and unplug it. If the small piece of plastic has fallen into the cartridge, it must be removed, as this can damage your cartridge or cause print defects. If the piece remains in the tool, wait for the tool to cool down and pry it out.
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner stops flowing before the cartridge is full, simply
remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once the cartridge is full seal the hole with the plug.
Do not press down on the plug since the cartridge is resting on a table this can actually damage the photo-optic drum. Instead hold one end of the cartridge up off the table and twist the plug until it fully sealed. Now gently shake the cartridge side to side to distribute the toner.
|
To purchase Toner Refills visit our secure Internet Shop @ 
